Software for the Pro-Link Plus and Pro-Link Graphiq

Software Kit Includes:

MPI-201007 DDEC I & II Cartridge
MPI-208026 DDEC II & III Cartridge
MPI-802115 DDEC III & PCMCIA Card
MPI-401003 GM 12 Pin Adapter

DDEC I AND II

Features:

Monitor real-time ECU input and output status
Display data parameters and values in English or metric
Create custom data lists
Read and clear diagnostic fault codes
Reference ECU serial number, part number and revision number
View EEPROM vehicle /engine calibrations and configure with password:

Speed settings and limits
Idle shutdown options
VSG options
Engine protection shutdown options
Cruise control
and more

Fuel injector response times
Automatic and manual cylinder cutout for determining power contribution
Access and reset total engine and trip information
Monitor ECU switch / light status
Display diagnostic information for dual fuel vehicle (CNG and diesel)
Save and print fuel usage information for fleets up to 25 vehicles:

Truck, driver, mileage and date
Fuel (total)
Hours (total)
PTO Hours
Average Miles per Gallon
Trip Miles and Gallons
Isolate intermittent problems in Snapshot mode recording and playback
Printer output for printing data and test results

SYSTEM SUPPORTED: DDEC I & II ELECTRONIC ENGINE SYSTEM

This cartridge is for use with the Pro-Link scan tool for diagnosing Detroit Diesel DDEC I / II electronic engine controller systems. Simple menus allow technicians to easily navigate through a variety of diagnostic functions. Capabilities include monitoring the vehicle ECU' inputs and outputs, fault code messages, view and change programmed EEPROM data to name a few. It provides access to a full range of comprehensive OEM proprietary data and tests for maintaining top vehicle performance and keeping it on the road.

DDEC II AND III

Features:

Support for Series 2000 and 4000 Engines with USA and ISO firing order selection
Support for Electronic Synchronized Shift (ESS) transmission view and reprogramming feature
VSS anti-tamper reprogramming
J1708 to PC link feature
Cylinder cutout feature
Function lockout for enhanced security of calibration data
Display and reprogram EEPROM calibration data
Display and reprogram injector calibration
Display and reprogram parameter descriptions and values in English or metric units

Additional Features:

View and clear diagnostic codes
Activate outputs to perform circuit tests
Engine total and trip information
Snapshot feature for trouble shooting intermittent faults
Programmed with simple menus to easily navigate technicians through a variety of diagnostic functions
Printer output allows you to print standard data list, custom list, diagnostic codes, calibration configuration, trip information or snapshot data

ECM output options

Turbo recirculation

Pressure regulation solenoid

PWM option

Injector pump

Transmission options

RS9, RSX9-A, RSX9-B, RSX9-R, RS10, RSX10

J1939 engine brake level

Clutch test enabled

DATA LIST PARAMETERS:
Active codes Inactive codes Engine RPM Crankcase pressure Bypass valve Loop status Exhaust gas AFR Engine load percent Torque Lb-Ft (Nm) ECM volts Vehicle speed MPH / KPH Boost PSI Injection pressure Oil, coolant, fuel and air inlet temperature Intercooler temperature Oil, fuel, barometric, crankcase, coolant and external pump pressure Oil and coolant level	Cruise set MPH/KPH Synchronous reference sensor received Idle speed RPM Engine governor Percent torque limit Idle shutdown information Smoke control Dash light status Stop engine override switch Actuator driver High gear switch Power control switch Cruise control ON/OFF switch Brake/clutch switch Resume/accel switch R1 air inlet pressure R2 air inlet pressure

DDEC III & IV ENGINE SUITE 8.1 PCMCIA CARD

The Detroit Diesel application software provides the capability to reprogram and diagnose Detroit Diesel DDEC III and IV electronic systems. To address advanced capabilities provided by Detroit Diesel, the MPC uses PCMCIA cards. The card is plugged into the back of the unit, and provides additional functions unique to Detroit Diesel. The following list contains all of the features and functions available with this card.

Features:

Covers diagnostics for DDEC ECM firmware through version R33 for complete support of fault code data
Enhanced EGR diagnostic support
Fault code date and time logging
2nd page fault data supported for active faults
ECM date and time display
Progressive shift parameters

Additional Features:

Data list parameters
Trouble codes with text descriptions
Perform diagnostic tests
Speed limit parameters
Exhaust temperature monitoring
English/Metric menu saves setting to PCMCIA card
Snapshot recording
Create custom data list

DDEC III Engine Features:
Displays the specific DDEC system type, including DDEC IV Increased half engine operation functionality Support of low gear torque limiting Supports cutout for natural gas engines Additional ESS transmission functionality	Added total engine revolutions to the engine data menu Support for optimized load Reset AFR learn table on natural gas engines New maintenance monitoring Monitor systems Perform diagnostic test Modify system/data

DDEC Marine Application Features:

Supports marine controls version 2.0, 2.5, 3.0
Separated menus for marine controls specific parameters
Marine engine parameters integrated with standard engine parameters
Menu option allows for parameter names to switch from standard to marine descriptions
Data list enhancements

Series 638 Features:

Print option added
Data list
Defect codes

View codes
Clear codes

I/O Status

Operating System Enhancements:

Custom data list can be saved to PCMCIA
Data list wrap
Includes data freeze feature
Snapshot trigger on any fault
Faster and easier print function
Side button 2 hot key
Historic codes, print 2nd page data
Print all ECM data
Print 2nd screen data inactive faults
More descriptive headings
Application version number included
Tool ID display enlarged
Marine menu data list enhancements